View D200_43469.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
D200 Series
Single & Dual Output Miniature, 2W SIP DC/DC Converters
Electrical Specifications
Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Key Features:
Parameter
Conditions
Min.
Typ.
Max. 5.5 13.2 26.4 52.8 0.3
Units
2W Output Power Miniature SIP Case Input Voltage Range Single & Dual Outputs 1,000 VDC Isolation Input Filter >2 MHour MTBF Reverse Polarity Input Current Output 28 Standard Models Industry Standard Pin-Out Parameter
Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit
5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 48 VDC Input 43.2 48.0 Internal Capacitor
VDC
A Units % % % mV P - P % %/C
Conditions
Min.
Typ. 1.0
Max. 3.0 1.0
Dual Output , Balanced Loads For Vin Change of 1% 1.2 See Model Selection Guide 120
75 0.02 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 60 125 Min. Ambient Case -40 Typ. +25 Max. +85 +100 +125 95 Typ. Max.
General
Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Units VDC M pF kHz Units C C C %
Environmental
Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions
-40 Free Air Convection RH, Non-condensing
Physical
MicroPower Direct
232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com
Case Size (5V, 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight
0.76 x 0.24 x 0.37 Inches (19.5 x 6.0 x 9.5 mm) 0.76 x 0.28 x 0.37 Inches (19.5 x 7.2 x 9.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.09 Oz (2.7g) Conditions MIL HDBK 217F, 25C, Gnd Benign Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. 2.0 Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 55.0 260 650 Typ. Max. Units MHours Units
Reliability Specifications
Parameter MTBF
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
VDC
Lead Temperature Internal Power Dissipation
C mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model Number D201 D202 D203 D204 D205 D206 D207 D211 D212 D213 D214 D215 D216 D217 D221 D222 D223 D224 D225 D226 D227 D231 D232 D233 D234 D235 D236 D237 Notes:
1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 F) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. All 3.3, 5 and 5 VDC output models may be operated to +85C ambient with an unobstructed airflow of 3.6 ft/S (1.1 m/S). 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an input capacitor (10 F) may enhance performance in some applications. An output capacitor (1.0 F to 10 F) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to 47 uF (dependent upon the application). 5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating.
Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 533 35 3.3 400.0 10.0 12 75 1,000 5 4.5 - 5.5 513 35 5.0 400.0 8.0 12 78 1,000 5 4.5 - 5.5 495 35 12.0 165.0 3.0 8 80 1,000 5 4.5 - 5.5 499 35 15.0 133.0 2.5 8 80 1,000 5 4.5 - 5.5 533 35 5.0 200.0 4.0 12 75 1,000 5 4.5 - 5.5 504 35 12.0 83.0 1.5 8 79 1,000 5 4.5 - 5.5 501 35 15.0 66.0 1.0 8 79 1,000 12 10.8 - 13.2 204 25 3.3 400.0 10.0 8 67 500 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500 12 10.8 - 13.2 196 25 12.0 165.0 3.0 8 85 500 12 10.8 - 13.2 200 25 15.0 133.0 2.5 8 83 500 12 10.8 - 13.2 216 25 5.0 200.0 4.0 8 77 500 12 10.8 - 13.2 201 25 12.0 83.0 1.5 8 82 500 12 10.8 - 13.2 200 25 15.0 66.0 1.0 8 82 500 24 21.6 - 26.4 92 10 3.3 400.0 10.0 8 74 200 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200 24 21.6 - 26.4 101 10 12.0 165.0 3.0 8 81 200 24 21.6 - 26.4 101 10 15.0 133.0 2.5 8 82 200 24 21.6 - 26.4 108 10 5.0 200.0 4.0 8 77 200 24 21.6 - 26.4 102 10 12.0 83.0 1.5 8 81 200 24 21.6 - 26.4 99 10 15.0 66.0 1.0 8 84 200 48 43.2 - 52.8 59 10 3.3 400.0 10.0 8 70 100 48 43.2 - 52.8 54 10 5.0 400.0 8.0 8 77 100 48 43.2 - 52.8 51 10 12.0 165.0 3.0 8 81 100 48 43.2 - 52.8 50 10 15.0 133.0 2.5 8 82 100 48 43.2 - 52.8 54 10 5.0 200.0 4.0 8 76 100 48 43.2 - 52.8 51 10 12.0 83.0 1.5 8 81 100 48 43.2 - 52.8 50 10 15.0 66.0 1.0 8 82 100
Pin Connections
Pin 1 2 4 5 6 Single +Vin -Vin -Vout No Pin +Vout Dual +Vin -Vin -Vout Common +Vout
Mechanical Dimensions
Derating Curve Capacitive Load
Single Output (F Max) 470 Dual Output (F Max) 390
Notes: All dimensions are typical in inches (mm) Tolerance x.xx = 0.01 (0.25)
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
Pin 1 is marked by a "dot" or indentation on the side of the unit For 5V, 12V & 24V input models, "W" = 0.24 in (6.0 mm) For 48V input models, "W" = 0.28 in (7.2 mm)
TEL: (781) 344-8226
FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com

▲Up To Search▲

Price & Availability of D200

	To Download D200 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .